Why now and not later
In a finished house, the cable route sets the price: loft, crawl space, concrete floor slab, plastered wall. In the article on the cost of network cabling in an existing house I work with 1–3 hours per socket. In a new build, or a full renovation with open walls, the route is clear: the cable runs through conduit or the service void, gets terminated and tested. That is typically closer to half an hour to an hour per point – with no visible trunking, no extra holes through finished walls and no spots you simply cannot reach any more.
Also, Wi-Fi does not replace cable. Access points, TVs, cameras and the home office are more reliable on a cable, and Wi-Fi itself only becomes good once the access points are wired.
Principle 1: star cabling to the network cabinet
Every point gets its own cable all the way back to the central cabinet. No cable is daisy-chained from socket to socket, and no switch disappears behind a wall panel. In the cabinet, all cables end on a patch panel, with short patch leads to the switch and router. That way any socket can later be moved, tested or switched off without tools.
In large houses, or when there is a second building, a small secondary cabinet can make sense. Same principle on a smaller scale, with a generously sized link between the two – or fibre if two separate buildings are involved (see Connecting a guest house, garage or workshop).
The network cabinet: location, size, airflow, power
The cabinet is the heart of the network. This is where the fibre, every cable in the house, the router and the switch end up, often along with a NAS, a camera recorder and a small UPS. Four things decide whether it is well planned:
- Location: as central as possible so no cable is longer than necessary (copper is limited to 100 metres per run – rarely a problem in a house, but winding routes eat metres faster than you think). Good: utility room, technical room, storeroom, a hall cupboard. Poor: bathroom, cold loft, bedroom (fan noise, LEDs), unheated garage.
- Size: The small flush-mounted media enclosures often fitted in new Swedish houses (a “mediacentral”) are designed for the fibre box and a router – not for a patch panel, a PoE switch and a NAS. Plan for a 19-inch wall cabinet of roughly 9–12U, or a recess where one will fit later. Depth must suit the switch and NAS.
- Airflow: Router, PoE switch, NAS and UPS together easily give off several tens of watts to over a hundred, especially when the switch powers access points and cameras. A closed cabinet in a tight cupboard with no air exchange gets too warm in summer. Ventilation openings, some space to the wall, no airtight recess.
- Power: At least two, ideally four power sockets right at the cabinet, preferably on their own circuit. That is the electrician’s job and belongs in the electrical plan. Leave room for a UPS as well.
Which cable: Cat6 or Cat6A?
| Cable | Speed | Use in the house |
|---|---|---|
| Cat6 | 1 Gbit/s over 100 m; 10 Gbit/s up to around 50 m depending on conditions | Ordinary sockets: TV, desk, games console, printer |
| Cat6A | 10 Gbit/s over the full 100 m | Access points, link to a secondary cabinet, spare runs |
| “Cat7”, “Cat8” | no benefit in a normal RJ45 home installation | not needed |
New Wi-Fi 7 access points often have 2.5 Gbit/s or faster ports. Cat6 normally handles 2.5 and 5 Gbit/s over typical house lengths, but Cat6A gives headroom for the next twenty years – and the extra cost barely registers in a new build. What matters is that cable, sockets and patch panel are the same category and that you buy solid copper. Cheap “CCA” cable (copper-clad aluminium) does not meet the standard and runs warmer with PoE. Cat6A is thicker and stiffer, which affects conduit sizing.
Conduit: size, bends, draw wire
Conduit is insurance against the future. A cable lying in conduit can be swapped for a better one or joined by a second. Rules that work:
- Diameter: 20 mm is tight even for a single Cat6 cable; 25 mm is the safe choice for one or two cables. For main routes, such as from the cabinet to the upper floor or the loft, 32 mm or two conduits.
- Bends: as few as possible. After two 90-degree bends pulling gets hard; add a pull box in between instead.
- Draw wire: in every conduit, including the empty ones. Without one, a conduit is often useless once the wall is closed.
- Separate from mains: never run network cable in the same conduit as 230 V. Keep distance on long parallel runs and cross at right angles.
- Mind the vapour barrier: in most Swedish timber houses the plastic membrane sits behind a service void. Cables and conduit belong in that void so the membrane is not punctured for every socket. That is the builder’s responsibility, but the network points need to be known in time.
- Spare conduit: one empty run from the cabinet to the loft, one to the crawl space or technical room, one heading outside towards the garage or garden.
How many sockets per room?
| Room | Suggestion | Why |
|---|---|---|
| Living room (TV wall) | 2–4 ports | TV, media player, console, soundbar – or a small switch at a double socket |
| Study | 2–4 | PC, docking station, printer, possibly a second desk |
| Bedroom | 1–2 | TV, future study |
| Children’s room | 2 | Console, PC – rooms change use |
| Kitchen | 1 (optional) | Connected appliances, tablet, speaker |
| Technical room | 1 per device | Heat pump, ventilation, inverter or charger, if they have a network port |
| Garage / carport | 1–2 | EV charger, workbench, future access point |
Rule of thumb: one cable too many rather than one too few. An unused cable costs little in a new build; a missing one costs many times more later. On EV chargers, see Charging an EV at home in Sweden – many chargers can be controlled over Wi-Fi or mobile data, but a cable is more dependable.
Which smart home devices also need a cable, a socket or conduit is covered in Smart home in a new build: wired or wireless.
Ceiling access points – with PoE
An access point covers best from the ceiling, in the middle of the area it serves, clear of metal and not inside a cupboard. It gets data and power over a single network cable (PoE). Plan for:
- at least one ceiling point per floor, two for large floor plans, thick internal walls or concrete slabs,
- an extra point upstairs or towards a gable that you may not use today,
- Cat6A to every AP point,
- a switch in the cabinet with enough PoE budget. Common classes: 802.3af up to 15.4 W, 802.3at up to 30 W, 802.3bt up to 60 or 90 W per port (figures at the switch). Newer access points often need more than 802.3af – the data sheet decides.
Pinning down exact AP positions needs the floor plan and details of walls and floors. An on-site survey is only possible once the walls are up – which is another reason to add one point too many.
Outside: cameras, doorbell, outdoor AP
Outdoor points are especially cheap in a new build, because the cable can be run from inside into the eaves or the facade before cladding and sealing are finished. Typical points:
- Cameras: at house corners under the eaves, above the front door, at the carport or driveway. A PoE camera needs nothing but one network cable. Exact positions depend on what the camera needs to see.
- Video doorbell: a network cable next to the front door, even if you are planning a wireless doorbell today.
- Outdoor access point: for the terrace, the garden or as a bridge to the garage – one point under the eaves facing the plot.
- Conduit into the garden: if a guest house, workshop or a gate with a camera comes later, a conduit already in place saves drilling through the foundation or facade again.
Penetrations to the outside must be sealed and shed water properly. Agree this with the builder.
Fibre entry: from the plot into the cabinet
Most network owners (municipal networks, fibre associations, Telia/Skanova and others) bring the fibre to or through the outer wall. Who digs on your own plot, where the protective duct should end and what requirements apply is set out in your network owner’s connection terms – read them before the digger arrives, and order early, since lead times are often long.
Indoors, the key point is that the fibre box (media converter, “kundnod”) ends up in the network cabinet, not behind the fridge in the utility room. That takes a continuous conduit from the entry point to the cabinet, a power socket for the box and an agreement with the network owner so the technician pulls the fibre all the way there. What to do with router and Wi-Fi after installation is covered in Fibre installed – what next?
No fibre yet? Plan a cable route to a window or gable where a 4G/5G router or an external antenna can go.
Documentation: photos, numbers, test report
The cheapest insurance in the whole project: before the walls are closed, photograph every wall with a folding rule in the picture wherever cables or conduit run. In addition:
- the same number on each socket and its patch panel port,
- a floor plan with the points and conduit routes marked,
- a test report for each cable (at least continuity and wiring, ideally a certification test),
- one copy in the cabinet and one digital.
Whoever hangs a picture or opens a wall in ten years will thank you. And when you sell the house, clean network documentation is a plus.
What it costs: now and later
A typical example for a two-storey house: 10 sockets, 3 AP points and 3 outdoor points – 16 cables. Approximate labour at 1,000 SEK per hour:
| New build, conduit in place | Retrofit in a finished house | |
|---|---|---|
| Labour per point | approx. 0.5–1 h | approx. 1–3 h |
| Labour for 16 points | approx. 8,000–16,000 SEK | approx. 16,000–48,000 SEK |
| Visible trunking, compromises | none | often |
| Outdoor points | from inside into the eaves | drilling through a finished facade |
Materials come on top in both cases: cable, sockets, patch panel, cabinet, switch. These are estimates for typical situations; the real price depends on layout, wall construction and access. The earlier the plan exists, the more likely the cables can go in alongside the other installations.
ROT and RUT: what applies to a new build?
- New construction: According to Skatteverket there is no ROT deduction for new construction or for completing a house – including a detached outbuilding. Whether RUT applies to a network installation in a house that is still being built and not yet lived in is not clearly settled. Check with Skatteverket before counting on it. Often the cabling is part of the builder’s contract anyway.
- Renovating an existing house: A network with cables and sockets in the home is an IT service that qualifies for RUT (50% of labour). Drilling through the facade, chasing walls and burying cable on the plot may instead count as ROT work (30%). For conversions and extensions, ROT only applies once five years have passed after the year the house was completed (its “värdeår”).
- Never deductible: materials, travel and remote planning. Installing cameras and alarms does not qualify for RUT either.
- ROT and RUT combined are capped at 75,000 SEK per person per year, of which ROT at most 50,000 SEK. You need to pay tax in Sweden to benefit. More in IT help at home and the RUT deduction.
Who does what?
Network cabling is low voltage and needs no electrical licence in Sweden. Anything at 230 V – sockets at the cabinet, a dedicated circuit, combined power and data boxes, earthing – must be done by a registered electrical installation company. Conduit in walls and penetrations through the building envelope are usually laid by the builder or the electrician in the same step. I plan the network, provide the drawings and notes for electrician and builder, pull and test the network cables and set up the cabinet, router and Wi-Fi.
Checklist before the walls close
- Cabinet location decided: central, dry, frost-free, ventilated, room for 9–12U
- 2–4 power sockets at the cabinet in the electrical plan
- Fibre ordered, entry point known, conduit from entry to cabinet
- Dedicated cable from each socket to the cabinet (star), double sockets at TV and desk
- At least one ceiling AP point per floor, Cat6A
- Outdoor points for cameras, doorbell, outdoor AP
- 25 mm conduit with draw wire, spare conduit to loft, crawl space and outside
- Network kept separate from 230 V
- Photos of all open walls with a scale, sockets numbered to match the patch panel
- Test report before handover
Frequently asked questions
Isn’t Wi-Fi enough in a new house?
For phones and tablets, yes – but only if the access points are wired. TVs, desks and cameras are more reliable on a cable. In a new build a cable costs little; retrofitting costs many times more.
What size conduit do network cables need?
25 mm for one or two Cat6 or Cat6A cables, 32 mm or two conduits for main routes. Few bends and a draw wire in every conduit.
Can I get ROT or RUT for the cabling in a new build?
ROT does not apply to new construction. Whether RUT applies before you move into a newly built house is not clear – ask Skatteverket. When renovating an existing house, network installation with cables and sockets qualifies for RUT.
Where should the network cabinet go?
As central as possible, dry, frost-free and ventilated, with its own power sockets – for example in the utility or technical room. Not in the bathroom, a cold loft or a bedroom.
No affiliate links. Recommendations are based purely on hands-on experience.
Building or renovating? For this there is the Plan Network new build at a fixed price of 3,500 SEK (about 3.5 hours; private customers incl. VAT, businesses excl. VAT). I go through your floor plan, mark cabinet, sockets, access points, outdoor points and conduit routes, provide a materials list and notes for your electrician and builder, and walk you through it by video or phone – in English, Swedish or German. Reply within 24 hours.
Network cabling in Sundsvall Book a free call